╨╧рб▒с>■  ')■   &                                                                                                                                                                                                                                                                                                                                                                                                                                                ье┴7 Ё┐bjbjUU .7|7|       lиииииии╝ЦЦЦЦ в╝/╢┬┬┬┬┬┬┬┬╥╘╘╘╘╘╘х  д╘и┬┬┬┬┬╘ ии┬┬щ   ┬"и┬и┬╥ ┬╥ ╞ ╥ии╥┬╢ W║ИС╚╝┌Цф(╥╥ 0/╥й й ╥ ╝╝ииии┘ HOODOO 2 LIFT INSTRUCTIONS. REAR Ц To fit spacers at the rear, refer to the Mk 1 instructions for this procedure. They are identical. FRONT Ц Jack up under lower arm on one side and support vehicle under cross member using an axle stand. Remove wheel. Remove brake caliper and support out of the way. Remove hub nut and central splined unit complete with disc. Undo the three 13mm nuts securing the top and lower ball joints, swing hub unit to the rear, pivoting on the track rod and clearing the CV joint, and support. Remove shock absorber. You can just remove the lower mounting bolt if necessary, in which case compress the bottom upwards and secure with a piece of string. Lower the jack and pull clear once contact is lost, then push the arm down further and remove the spring. Remove the Lada rubber spring seat, complete with the brass rubber holder, then fit the spacer over the BN tube, followed by the Lada spring seat and brass holder. Also dry fit the spring. It may be necessary to trim the brass holder a bit to allow proper seating of the spring. Once satisfied with the fit, fit everything in place over the upper cone. You may wish to weld the BN tube to the base of the cone. Remember to ensure the hollows for the coil ends are correctly positioned top and bottom so the spring will seat properly. As on the Mk 1 kit, cut 1Ф off the upper bump stop, and space out the pivot bolts of the upper arm by 3mm. Now refit everything, reversing the removal procedure. Once both sides are complete, check the camber angle of the front wheels. They should be vertical. If leaning in at the top (negative camber) jack up under the lower arm, remove wheel, and insert some more washers (the same thickness on the bolts front, rear, and both sides. Note that jacking under the lower arm removes pressure from the upper arm, and there is no danger of it flying off when the pivot bolts are released (one at a time!). NOW GET THE TRACKING DONE!! It will be toeing out as a result of lifting. Also note that fitting this kit is entirely the responsibility of the installer!! BN tube dimensions - 80mm ID. 4mm wall thickness. 60mm tall. !;√>*CJ =>ноп╝1TЪы2хdyж ╝ ╙ U V г д u v ╒ ╓ <=]Ч¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤¤■Ч╚╔╘¤¤¤¤,1Рh░В. ░╞A!░"░#Ра$Ра%░░─░─ Р─ i8@ё 8 NormalCJ_HaJmH sH tH <A@Є б< Default Paragraph Font     =>ноп╝1TЪы2хdyж╝╙UVгдu v ╒ ╓ < = ] Ч ╚ ╔ ╘  Ш0ААШ0ААШ0ААШ0ААШ0ААШ0ААШ0ААШ0ААШ0ААШ0ААШ0ААШ0ААШ0ААШ0ААШ0ААШ0ААШ0ААШ0ААШ0ААШ0ААШ0ААШ0ААШ0ААШ0ААШ0ААШ0ААШ0ААШ0ААШ0ААШ0ААШ0ААШ0ААШ0АА Ч  v}:> AIP X  33   jC:\Documents and Settings\Administrator\Application Data\Microsoft\Word\AutoRecovery save of Document1.asd NC:\Documents and Settings\Administrator\Desktop\HOODOO 2 LIFT INSTRUCTIONS.doc NC:\Documents and Settings\Administrator\Desktop\HOODOO 2 LIFT INSTRUCTIONS.doc NC:\Documents and Settings\Administrator\Desktop\HOODOO 2 LIFT INSTRUCTIONS.doc @ @@  Unknown            GРЗz А Times New Roman5РАSymbol3&Р Зz А Arial"qИЁ╨hH▌├ЖХф├жj▌├Ж'Ъ" $Ёе└┤┤ББ20d7 2ГЁ  ; HOODOO 2 LIFT INSTRUCTIONS  ■ рЕЯЄ∙OhлС+'│┘0иШафЁ№$ 0< X d p |ИРШаф< HOODOO 2 LIFT INSTRUCTIONS    Normal  rm3rmMicrosoft Word 9.0 @к┐r@D#cSР╚@°3гNР╚@;yС╚Ъ" ■ ╒═╒Ь.УЧ+,∙о0$ hp|ДМФ Ьдм┤ ╝ ф 7 а < HOODOO 2 LIFT INSTRUCTIONS Title ■   ■   ■    !"#$%■   ¤   (■   ■   ■                                                                                                                                                                                                                                                                                                                                                       Root Entry         └F╨i═ИС╚*А1Table            WordDocument        .SummaryInformation(    DocumentSummaryInformation8            CompObj    jObjectPool            ╨i═ИС╚╨i═ИС╚            ■                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                           ■       └FMicrosoft Word Document MSWordDocWord.Document.8Ї9▓q